Siemens Home Appliances
Follow the below instructions to install your washing machine.
To ensure that your Siemens washing machine runs safely and reliably, it must be correctly installed. In order to achieve this, there are a few points to note. You can install a freestanding washing machine with our simple guidance below, but if you are unsure you should always consult a qualified professional.
Please do not use the information below as a substitute for the information contained in your installation manual.
Information how to install and set-up your washing machine you will find in the appliance documentation (use manual, installation instructions) of your washing machine.
Setting up your new washing machine.
Follow the below instructions to install your washing machine.
To ensure that your Siemens washing machine runs safely and reliably, it must be correctly installed. In order to achieve this, there are a few points to note. You can install a freestanding washing machine with our simple guidance below, but if you are unsure you should always consult a qualified professional.
Please do not use the information below as a substitute for the information contained in your installation manual.
Information how to install and set-up your washing machine you will find in the appliance documentation (use manual, installation instructions) of your washing machine.
Placing the machine
To prevent it from "wandering", the washing machine must be positioned such that it is stable. This means that the surface on which it is installed must be firm and level. Soft floors and floor coverings are therefore not suitable.
If you are installing the washing machine on a base, you must secure the appliance feet with floor fixing brackets.
If you have a wood beam floor, if possible, you should install the washing machine in a corner on a water-resistant wooden board (at least 30 mm thick) that is screwed securely to the floor.
Otherwise, the appliance may "wander" and tip/topple from the base when spinning.
Once the appliance is in place, remove all four of its transit bolts.
Remove transit bolts
The washing machine drum is secured during delivery with four transit bolts. It's vitally important that these are removed before the appliance is installed and used. They are located at the back of the appliance and are removed with a spanner. Replace them with the blanks provided. Keep the transit bolts safe in case you need to transport the washing machine in the future.
Connection to cold water pipe
You will then need to connect the cold water pipe and waste pipe connection. Check the installation instructions to identify these pipes. You will need to connect the cold water pipe to a cold water tap which is usually marked blue. This connection supplies water to the appliance.
You can stop the water supply by turning the valve. Connect the cold water pipe to the cold water tap, tighten it fully by hand rather than with a tool and then turn the valve back on. Make sure the cold water pipe is not kinked.
Waste water connection
There are two options for the waste water connection, depending on the plumbing within your home. You can connect to a normal stand pipe which should be at least 30 cm high to ensure that no waster water will re-enter the appliance but lower than the height of the appliance itself.
You will find one of two waste water pipe holder depending upon the appliance you're fitting.
Use the holder supplied to secure the waste water pipe into position.
Alternatively you can attach the waste water pipe to a connection underneath the sink. Under the sink you'll see the waste connections for the appliance. These are called traps and there are a number of different types. If you are connecting to the trap for the first time, you will need to remove a blanking cap which acts as a stopper.
Check there are no kinks in the pipe and connect the waste water pipe to the trap securely.
Electric connection
Washing machines will plug into a standard socket. Contact a qualified professional if you have any questions or concerns about the electrics.
Levelling the washing machine
You should then check that the appliance is level by using a spirit level. This is particularly important for the installation of a washing machine in order to avoid problems with unbalanced loads. You can raise and lower the feet on the appliance to adjust the appliance level. Also ensure the appliance is stable and that it doesn't rock. If so, adjust the feet so that it is completely stable.
Testing
To complete the installation, switch on the appliance and run a rinse programme, checking carefully for any leaks. If none are found, move the washing machine into its final position ensuring it remains stable.
Need more info?
Get in contact with Siemens Home Appliances Service or check the appliance documentation of your appliance.
